Engine Shop Visit: Time on Wing, Overhaul Costs and Who Pays

by | Nov 16, 2026 | Luftfahrtwelt | 0 comments

At the peak in 2025, 648 brand-new airliners were sitting on the ground with nothing wrong with their wings, cabins or avionics. They were waiting for engines. Their Pratt & Whitney geared turbofans needed shop visits, the shops were full, and the parts were not there.

That figure comes from a June 2026 report on single-aisle engine maintenance published on IATA’s website and prepared by consultancy Emerton. It is the most dramatic recent illustration of a simple truth about airline economics: the engine shop visit is where the money is, and the airline is often the party with the least control over it.

Kurzinfo

  • Shop visit: Engine removed, partly or fully disassembled, repaired and run in a test cell
  • Mature time on wing: Typically 15,000-20,000 flight cycles for single-aisle engines in normal environments (IATA/Emerton, 2026)
  • GTF today: 5,000-6,000 cycles, before powder-metal inspections (IATA/Emerton)
  • Typical cost: Often over USD 3-4 million, depending on engine, workscope and parts
  • Market: Engine MRO about USD 50 billion in 2024, 40-50% of all aircraft MRO spending
  • Power by the Hour: Fixed cost per flying hour, first offered in 1962 for the Viper engine; Rolls-Royce trademark
  • Peak grounding: 648 GTF-powered aircraft awaiting shop visits in 2025

What a shop visit actually is

A lot of engine maintenance happens with the engine still hanging under the wing. Borescope inspections, swapping line-replaceable units and troubleshooting are on-wing work, done by the airline or its line-maintenance provider. A shop visit is different: the engine comes off the aircraft, goes to an overhaul shop, is partly or fully taken apart and, after a major visit, run in a test cell before it is released.

The IATA report lists the usual reasons an engine comes off. The big one is overhaul, a major shop visit to replace life-limited parts. Then there is performance restoration, when the engine has lost too much exhaust gas temperature (EGT) margin or fuel efficiency. Engines also come off for condition-monitoring findings such as vibration, oil consumption or borescope damage, for bird strikes and other foreign-object damage, for airworthiness directives and service bulletins, and for purely commercial reasons such as returning an engine at the end of a lease.

The test cell building of N3 Engine Overhaul Services in Arnstadt, Germany, at dusk
The engine test cell at N3 Engine Overhaul Services in Arnstadt, Germany. Major shop visits end with a test-cell run before the engine is released. Photo: COM N3 / Wikimedia Commons, CC BY-SA 4.0

Time on wing: the number that matters

The interval between shop visits is called time on wing, and it is usually measured in flight cycles: one take-off and one landing. For a mature single-aisle engine in normal conditions, the IATA report puts full time on wing typically between 15,000 and 20,000 flight cycles.

The hard ceiling is set by life-limited parts, the discs and shafts that must be replaced at a fixed number of cycles. On mature engines the high-pressure parts are typically limited to around 15,000 to 20,000 cycles, which for a single-aisle airliner means five to seven years of flying. An aircraft shuttling between New York and Washington can fly around 3,000 cycles a year and reach its first life-limited-part shop visit after about five years; one on longer sectors gets there later.

In practice, many engines come off before that ceiling. EGT margin erodes as hot-section parts wear, and those parts suffer most in hot, harsh environments. Fine dust, some particles a tenth the width of a human hair, can work into an engine’s core and wear down turbine parts, as GE Aerospace has described.

Lufthansa Technik shows the engine overhaul work in its engine shops.

Why new engines are spending so long in the shop

The new generation of single-aisle engines, CFM’s LEAP and Pratt & Whitney’s GTF, is replacing the CFM56 and V2500. According to the IATA report, neither has yet reached its mature time on wing, so both need earlier and more frequent shop visits.

For the LEAP, the main fix has been hardware. On 6 December 2024 the US Federal Aviation Administration certified a high-pressure turbine durability kit for the LEAP-1A, comprising a new stage 1 blade, stage 1 nozzle and forward inner nozzle support, aimed especially at hot and harsh environments. GE Aerospace says its development drew on around 15 years of lab work and dust-ingestion tests in which engineers recreated the wear operators were seeing in the field.

“This new hardware is fulfilling our promise to ensure that LEAP-1A engines achieve the same level of maturity, durability, and time on wing that our customers have enjoyed with the CFM56 product line.”
Gaël Méheust — President and CEO, CFM International, on the FAA-certified LEAP-1A durability kit (GE Aerospace, December 2024)

The GTF’s problems have been deeper. The IATA report puts its current time on wing at 5,000 to 6,000 flight cycles, before counting the extra inspections for the powder-metal contamination issue in high-pressure turbine and compressor discs. That issue is what pushed up to 28 per cent of GTF-powered aircraft onto the ground in March 2025.

A bladed rotating stage from a Pratt and Whitney PW1000G geared turbofan engine on display
A bladed stage from a Pratt & Whitney PW1000G geared turbofan, on display at the MTU Aero Engines museum in Munich. Discs like this are life-limited parts, replaced at a fixed number of cycles. Photo: Zenwort / Wikimedia Commons, CC BY-SA 4.0

What an overhaul costs

There is no single price for a shop visit, and anyone who quotes one is guessing. The cost depends on the engine type, the workscope (which modules are opened and how deeply) and above all on which parts have to be replaced. A light visit to fix one module is a very different bill from a full performance restoration with a new set of life-limited parts.

The IATA report gives the industry-level picture. Engine maintenance was a market of about USD 50 billion in 2024, typically 40 to 50 per cent of all aircraft maintenance spending, and it consists mostly of shop visits that often exceed USD 3 to 4 million each, depending on engine type, workscope and parts needs. Life-limited parts are a big part of the bill, which is why a heavy visit that replaces them costs far more than a quick repair.

Volumes are rising fast. The report estimates that the CFM56 fleet alone was at its peak of around 2,000 shop visits in 2025, with more than 23,000 CFM56 engines still in service at the end of 2024. By 2040, it forecasts annual peaks of over 5,000 shop visits for the LEAP and 2,000 for the GTF.

Business Insider goes inside Delta’s engine shop to see how airline engines are taken apart and rebuilt.

Power by the hour

Because shop visits are huge, lumpy costs, airlines have increasingly stopped paying for them one at a time. The alternative was invented in 1962, when an engine and accessory replacement service was offered on a fixed cost per flying hour for the Viper engines of the de Havilland/Hawker Siddeley 125 business jet. Rolls-Royce, which owns the trademark, calls it Power by the Hour.

Today every big engine maker sells a version: Rolls-Royce TotalCare, GE TrueChoice, CFM Flight Hour Agreements and Pratt & Whitney EngineWise. The airline pays a rate for every hour flown, and the manufacturer takes on the cost and the risk of the shop visits. The logic is that the manufacturer only earns well when its engines stay on wing.

“TotalCare is charged on a fixed $ per flying hour basis, so we are only rewarded for engines that perform. This rewards reliability, a factor valued most highly by our airline customers.”
Rolls-Royce — On its TotalCare power-by-the-hour service

Law firm Morgan Lewis noted in 2024 that, for certain recently launched engine types, 100 per cent of airline customers have signed up for manufacturers’ rate-per-flight-hour agreements. For a new engine with unproven reliability, it is the airline’s insurance against exactly the kind of early-life trouble the GTF and LEAP have shown. The IATA report adds a downside: these all-inclusive deals also limit what independent repair shops can do.

Front view of the fan of a CFM International LEAP engine on an orange easyJet Airbus A320neo
A CFM LEAP engine on an easyJet A320neo. Like the GTF, the LEAP has not yet reached its mature time on wing, according to the June 2026 IATA engine-maintenance report. Photo: Actualcpscm / Wikimedia Commons, CC BY-SA 4.0

Why airlines barely own their engines

Put the pieces together and the airline’s relationship with its own engines looks thin. Analysts at CAPA put leasing at just over half of the world fleet, so on many aircraft the engines belong to a lessor. The leasing contract decides what condition they must be returned in, and the airline may pay maintenance reserves to the lessor as it flies.

If the engines are also on a flight-hour agreement, the manufacturer manages them through their life, shop visits included. Manufacturers even sell products for lessors, such as Rolls-Royce LessorCare and CFM’s Portable Maintenance for Lessors, which can give the lessor a credit or cash based on the flight-hour payments an airline made, for example when a lease ends. The airline flies the engine, but the owner and the manufacturer between them hold most of its value.

CNBC on why airlines such as American are working to make their engines last longer between shop visits.

That is also why an engine with plenty of time left before its next shop visit is a valuable asset in its own right. When an aircraft is retired, its engines can be parted out for their remaining life. For the people who finance airliners, the most important number is often the one that tells them how long until the next shop visit.

Sources: IATA / Emerton, “Single aisle aircraft engines MRO” (June 2026), GE Aerospace (LEAP-1A durability kit, December 2024), Rolls-Royce (TotalCare; Power-by-the-Hour 50th anniversary release), Morgan Lewis (rate-per-flight-hour agreements, 2024), CAPA Centre for Aviation

Header photo: J-C G / Wikimedia Commons, CC BY-SA 3.0

Häufig gestellte Fragen

What is an engine shop visit?
An engine shop visit is when a jet engine is removed from the aircraft and sent to an overhaul shop, where it is partly or fully taken apart, repaired and has worn or life-limited parts replaced. After a major visit it is run in a test cell before release. On-wing work such as borescope inspections is not a shop visit.
How much does a jet engine overhaul cost?
There is no single price. According to a June 2026 report published by IATA and prepared by Emerton, shop visits on single-aisle engines often exceed USD 3 to 4 million, depending on the engine type, the workscope and the parts needed. Replacing life-limited parts makes a visit far more expensive.
What is time on wing for a jet engine?
Time on wing is how long an engine stays installed between shop visits, usually counted in flight cycles. The IATA/Emerton report says mature single-aisle engines typically reach 15,000 to 20,000 flight cycles in normal environments, while the GTF currently manages about 5,000 to 6,000 cycles.
Why were so many A320neo jets with GTF engines grounded?
GTF engines have needed early and frequent shop visits because of maturity issues and the powder-metal contamination problem in turbine and compressor discs. With shops and spare parts stretched, 648 GTF-powered aircraft were grounded awaiting shop visits at the 2025 peak, up to 28 per cent of the fleet.
What does power by the hour mean for jet engines?
Power by the hour is an engine maintenance contract in which the airline pays a fixed rate per flying hour and the manufacturer covers the shop visits. It was first offered in 1962 for Viper engines on the HS 125 business jet. Rolls-Royce owns the trademark and sells it as TotalCare.
Why don’t airlines own their engines?
Many airlines lease their aircraft, and CAPA puts leasing at just over half of the world fleet, so the engines often belong to a lessor. Engines on flight-hour agreements are also managed through their life by the manufacturer, which covers the shop visits.

Ähnliche Beiträge

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *