Unit Load Device (ULD): How Air Cargo Containers Really Work

by | Nov 22, 2026 | Luftfahrtwelt | 0 comments

Look out of the window at any big airport and you will see them: rows of dented silver boxes on little trailers, each with a strangely sloping side, trundling behind a tug in a train of three or four. Nobody boarding a flight gives them a second glance. Yet your suitcase is probably inside one, and so is a good share of the world’s air freight.

They are called unit load devices, or ULDs, and the industry treats them very differently from the way passengers do. To the International Air Transport Association (IATA), a ULD is not packaging at all. It is a removable aircraft part, subject to airworthiness rules from design and testing through to repair, and when it is loaded and locked into the hold it is holding back tonnes of cargo in turbulence.

Here is what an air cargo container actually is: why it is shaped the way it is, what the code stencilled on its side means, how it locks into the floor, and who owns the roughly one million of them in service.

Kurzinfo

  • What it is: A unit load device (ULD): an aircraft container, or an aircraft pallet plus net
  • Status: A removable aircraft part under civil aviation airworthiness rules (IATA)
  • Most common type: LD3, IATA code AKE, half-width lower-deck container
  • AKE size: Base 156.2 x 153.4 cm, height 162.6 cm, max gross 1,587 kg (3,500 lb)
  • AKE empty weight: About 54 to 82 kg depending on build
  • Flotte: About 1 million ULDs in service, replacement value over US$1 billion (IATA)
  • Annual losses: About US$330 million a year in repair and loss (IATA)
  • Standards: IATA ULD Regulations; FAA TSO-C90; NAS 3610

What is a unit load device?

IATA defines a ULD as either an aircraft container or an aircraft pallet combined with a pallet net. The US Federal Aviation Administration’s guidance on cargo operations puts it more simply: a device for grouping, transferring and restraining cargo for transit. Either way, the idea is the same. Instead of throwing hundreds of individual bags and boxes into the hold by hand, the ground crew packs them into standard units on the ground, then rolls a few big units into the aircraft.

That changes everything about a turnaround. Loading can be done in the warehouse or baggage hall before the aircraft even lands. Each unit carries its own list of contents and is weighed, so the load planner knows exactly how much mass is going into each position of the hold. And unloading becomes a matter of minutes, not hours of hand work in a cramped compartment.

ULDs come in two basic forms. Pallets are flat, rugged sheets of aluminium with rims that the cargo net hooks into; freight is stacked on top, shaped to fit, and netted down. Containers are closed boxes, usually an aluminium frame with aluminium or polycarbonate walls, sometimes with a fabric or roller door at the front. Specialised versions carry horses, chilled pharmaceuticals or, in one case listed in the industry’s own code tables, sheep and goats.

Rows of AKE air cargo containers of several airlines on dollies under a terminal walkway at Melbourne Airport
AKE containers of several airlines waiting on dollies at Melbourne Airport. The cut-away lower corner on each box matches the curve of a wide-body fuselage. Photo: Sgroey / Wikimedia Commons, CC BY-SA 4.0

LD3 and AKE: the box everyone knows

The most common ULD in the world is the LD3, the half-width container that fills one side of a wide-body’s lower hold. Two of them sit side by side in each row. Its official IATA code is usually AKE, and the terms are often used interchangeably. LD3 describes the size and shape; AKE is the specific type designation, here a certified container with no forklift pockets in its base.

The numbers are surprisingly modest. According to the freight forwarder DSV’s published specifications, an AKE has a base of 156.2 by 153.4 centimetres, stands 162.6 cm tall and may be loaded to a maximum gross weight of 1,587 kg, which is 3,500 lb. Empty, an aluminium AKE weighs 82 kg on DSV’s sheet and 74 kg on IAG Cargo’s, while the Dutch manufacturer VRR advertises a fire-resistant version from 54 kg. IAG Cargo quotes an internal volume of about 4.2 cubic metres.

That sloping side is the giveaway. The lower outer corner of an LD3 is cut away because the box sits against the curve of the fuselage, and a square corner would simply not fit. The top of the container is 200.6 cm wide, but its base is only 156.2 cm. The full-width LD6 and LD11 do the same on both sides, and the main-deck containers of freighters use curved profiles to squeeze out every last cubic centimetre.

Lower-deck cargo loading on UPS Boeing 747-8F N633UP, filmed by Aeroscope Aviation.

Sizes are not universal across aircraft. LD3s fit the 777, 787, 747, A330, A350 and A380, but the narrower Boeing 767 was designed around the smaller LD2 and the full-width LD8. A reduced-height LD3, just 1.14 m tall, exists for the Airbus A320 family, one of the few narrow-bodies that can take containers at all. Boeing designed the 787, the 767’s successor, around the LD3 family to end that mismatch.

Reading the code: AKE 25699 KE

Every ULD carries an identification code, and once you know how it works you can read the box like a number plate. IATA’s system has three parts: a three-letter type prefix, a four- or five-digit serial number, and a two-character owner code, usually the airline’s IATA designator.

In the prefix, the first letter gives the category. A means a certified aircraft container and P a certified aircraft pallet; R is used for thermal containers such as the refrigerated RKN. The second letter gives the base size, and the third the container’s contour or the pallet’s restraint system. So AKE 25699 KE, stencilled on a Korean Air box at San Francisco, is an LD3-type certified container, serial 25699, owned by Korean Air. A pallet coded PMC is the standard 96 by 125 inch main pallet, known in the industry as an LD7.

The same logic explains the counting. Airlines do not measure hold capacity in cubic metres but in positions. One LD3 takes one position, an LD6 or LD11 takes two, and a PMC pallet occupies roughly three. That is why an airline’s cargo pages describe a 787-9 or 777 belly as a number of AKEs and pallets rather than a volume.

“ULDs are the only aircraft parts that leave the control of the airline, return after passing through many unregulated hands, and have an impact on flight safety.”
IATA — International Air Transport Association, Unit Load Devices programme page

How a ULD locks into the aircraft

Inside the hold, the floor is a cargo loading system: rollers and ball mats that let a 1.5-tonne container slide easily, powered drive units that push it along, side guides that keep it in its lane, and locks that pop up at each position. The FAA’s advisory circular on cargo operations is blunt about what happens next. A certified ULD only stays certified, it says, if it is restrained by the aircraft’s cargo loading system, such as pallet locks and side guides, and all of those restraints must be engaged.

VRR, which builds containers and pallets, describes the result neatly: the restraint system interfaces directly with the ULD, effectively locking it into place so that it becomes part of the aircraft. That is the whole point of certification. A certified ULD is built to the TSO-C90 standard, the FAA’s technical standard order for cargo pallets, nets and containers, and to the dimensional rules of the industry standard NAS 3610, and it is listed in the aircraft’s weight and balance manual.

Non-certified containers exist too, and the FAA’s guidance treats them with suspicion. Its circular warns that ULD designs may exceed the structural capability of an aircraft, and says non-certified units need extra analysis or must be tied down as if they were loose cargo. IATA’s own ULD Regulations, now in their 15th edition for 2027, add fresh rules for a fire-resistant container that must survive a fire load involving lithium-ion batteries.

Two Jettainer-branded LD8 containers coded DQF with the LH owner code on dollies at Boston Logan Airport
Two full-width LD8 containers, coded DQF, at Boston Logan. They are branded Jettainer, Lufthansa Cargo’s ULD management subsidiary, and carry Lufthansa’s LH owner code. Photo: 4300streetcar / Wikimedia Commons, CC BY 4.0

A million boxes, and nobody quite in charge of them

IATA estimates that there are about one million aircraft ULDs in service, with a replacement value of more than US$1 billion. That works out to an average of over a thousand dollars per unit, cheap by aircraft-part standards. The trouble is what happens to them. IATA puts the yearly cost of repairing and losing ULDs at about US$330 million, before counting the aircraft damage, delays and cancellations that badly handled units cause.

The reason is ownership. A ULD bearing an airline’s code leaves that airline’s hands the moment it is handed over to a ground-handling company, a freight forwarder or another carrier for a connection. It may be packed by a shipper, left at an outstation, stacked on a dolly in the rain or rammed by a tug. Many airlines have therefore stopped managing their fleets themselves.

Two specialists are the best-known names. Unilode Aviation Solutions says it manages the world’s largest outsourced fleet of ULDs and runs the largest global repair network for containers, pallets and galley carts. Jettainer, founded near Frankfurt in 2004 as a joint venture between Lufthansa Cargo and the US firm TrenStar, has been a wholly owned Lufthansa Cargo subsidiary since 2009 and manages a fleet that runs to six figures across hundreds of locations. That is why a Jettainer-branded box can still carry Lufthansa’s LH owner code.

“It is our clear ambition to bring the aviation industry to the next level of efficiency and supply chain transparency with digital ULDs.”
Benoît Dumont — Then CEO of Unilode Aviation Solutions, on fitting digital tags to its fleet (Air Cargo Week, April 2019)

Tracking the box

For decades, finding a missing container meant reading serial numbers off stencils and chasing paperwork. The fix now spreading through the industry is a small electronic tag. In 2019 Unilode began fitting its fleet with Bluetooth Low Energy tags, working with the manufacturer Nordisk on a mounting built into the edge rail of a pallet so that the tag survives forklifts and rollers. The tags report location and can log temperature and shock.

Readers installed in warehouses and on the ramp then pick the tags up as the units pass, so an operator can see where a container is without anyone walking the apron with a clipboard. Jettainer has built its business on its own ULD management software and app for similar reasons. For an airline, a box that can be found is a box that does not need to be replaced.

ULD containers on dollies beside a UPS Boeing 767-300F freighter with its main-deck cargo door open at Boston Logan
ULD containers from a UPS Boeing 767-300F freighter at Boston Logan, with the main-deck cargo door open and empty dollies lined up alongside. Photo: 4300streetcar / Wikimedia Commons, CC BY 4.0

Why the humble box matters

Air cargo is a business of tight margins and tighter timetables, and almost all of it rides in these boxes and on these pallets. A widebody passenger jet arrives, its belly is emptied of a dozen containers in minutes, and fresh ones roll in with suitcases, mail and freight, each weighed, coded and already planned into its position.

Unilode Aviation Solutions, the largest outsourced ULD manager, introduces its business.

Next time you look out at the apron, read the stencil on the nearest container. Three letters, a serial, an airline code. It tells you what the box is, what aircraft it fits, and who wants it back. And it is, quite literally, a part of the aeroplane.

Sources: IATA (Unit Load Devices; ULD Regulations), FAA Advisory Circular 120-85A, DSV, IAG Cargo, VRR, Unilode Aviation Solutions, Air Cargo Week

Header photo: Raimond Spekking / Wikimedia Commons, CC BY-SA 4.0

Häufig gestellte Fragen

What is a unit load device (ULD)?
A unit load device, or ULD, is an aircraft container or an aircraft pallet with a net, used to group baggage, mail and freight into standard units before loading. IATA classes ULDs as removable aircraft parts subject to airworthiness rules, because once locked into the hold they restrain the cargo in flight.
What is a ULD at an airport?
At an airport, ULDs are the silver containers and flat pallets towed on dollies between the terminal, cargo sheds and aircraft. Bags and freight are packed into them on the ground, weighed, and then rolled into the hold of a wide-body or some narrow-body aircraft, which makes loading and unloading much faster.
What is the difference between an LD3 and an AKE?
LD3 is the size and shape: the half-width lower-deck container with one sloping corner, two of which fill a row in a wide-body hold. AKE is the IATA type code for the most common certified LD3 version, without forklift pockets. In everyday use the two names are often used for the same box.
How much does a ULD cost?
IATA estimates about one million ULDs are in service with a replacement value of over US$1 billion, which implies an average of more than a thousand dollars per unit. Repair and loss of ULDs cost the industry about US$330 million a year, before counting the aircraft damage and delays caused by poor handling.
How much can an LD3 container hold?
An AKE, the most common LD3 container, may be loaded to a maximum gross weight of 1,587 kg, or 3,500 lb, according to DSV’s specifications. It has a base of 156.2 by 153.4 cm and stands 162.6 cm tall. IAG Cargo gives an internal volume of about 4.2 cubic metres.
How do you read a ULD code?
A ULD code such as AKE 25699 KE has three parts. The three-letter prefix gives the type, base size and contour, with A meaning a certified container and P a certified pallet. The four- or five-digit number is the serial, and the final two characters identify the owner, usually the airline.
Why are air cargo containers shaped with a slanted side?
Lower-deck containers such as the LD3 have a cut-away lower corner because they sit against the curved side of the fuselage. A square box would not fit, so the corner is removed to use as much of the hold as possible. An AKE is 200.6 cm wide at the top but only 156.2 cm at the base.
Who owns airline cargo containers?
Many ULDs belong to the airlines whose code they carry, but large fleets are managed by specialists. Unilode says it manages the largest outsourced ULD fleet, and Jettainer, a Lufthansa Cargo subsidiary since 2009, manages a six-figure fleet for many airlines. Units are tracked increasingly with Bluetooth tags.

Ähnliche Beiträge

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *