Aircraft Hydraulics Explained: The Hidden Muscles of a Jet

by | Nov 15, 2026 | Luftfahrtwelt | 0 comments

Sit over the wing on your next flight and watch what happens the moment the wheels touch. A row of panels on top of the wing slams upright, killing lift and pinning the aircraft to the runway. Nobody in the cockpit has the muscle to do that. Something else does: an oily fluid, squeezed to thousands of pounds per square inch.

Aircraft hydraulics are the muscles of a modern jet. They raise and lower the landing gear, move the flight controls, extend the flaps, steer the nosewheel and stop the aircraft with its brakes. They are so important that big jets carry three or more completely separate systems, and they are one of the least understood bits of the machine you are sitting in.

Kurzinfo

  • Principle: Pascal’s law: pressure on a confined liquid is transmitted equally in all directions
  • Typical pressure: A few hundred psi on light aircraft; 3,000 psi on most airliners; 5,000 psi on the largest transports
  • Main jobs: Landing gear, flight controls, flaps and slats, brakes, nosewheel steering, thrust reversers
  • Redundancy: Airliners carry three or more independent systems, such as A, B and standby on the 737 NG
  • Airbus names: Green, blue and yellow on the A320 family
  • PTU: Transfers power, not fluid, between two systems; the A320’s “barking dog”
  • Fluids: Mineral oil (MIL-H-5606, dyed red) or fire-resistant phosphate esters such as Skydrol on most airliners

A trick from the 17th century

The physics is old. Blaise Pascal worked out that pressure applied to a confined liquid is passed on undiminished to every part of it. Liquids barely compress, so if you push on the fluid at one end of a pipe, it pushes back with the same pressure at the other, however long and twisted the pipe is.

That gives engineers two superpowers. The first is force multiplication: a small piston pushing on the fluid can drive a much larger piston with far more force, because force equals pressure times area. The second is flexibility: you can generate the pressure in one place, by a pump on the engine, and use it anywhere you can run a pipe, from the tail to the nose gear.

“Hydraulic operations are also almost 100 percent efficient, with only negligible loss due to fluid friction.”
Bundesluftfahrtbehörde — Aviation Maintenance Technician Handbook, Airframe, Volume 2

Pump, reservoir, actuator

Every aircraft hydraulic system has the same basic cast, according to the FAA’s maintenance handbook: a pump to generate pressure, a reservoir holding spare fluid, an accumulator that stores pressure like a spring, a heat exchanger to cool the fluid, filters to keep it clean, and valves that send it where it is needed. At the far end sits an actuator, a cylinder whose piston turns fluid pressure into movement.

A maintainer reads a pressure gauge while bleeding air from an A-10 Thunderbolt II hydraulic system
A crew chief checks a pressure gauge while bleeding air out of an A-10’s hydraulic system at Davis-Monthan AFB in 2021. Air in the lines means a loss of hydraulic pressure. Photo: U.S. Air Force photo by Tech. Sgt. Sergio A. Gamboa / DVIDS

On a small aircraft, hydraulics may do nothing more than work the wheel brakes, at a couple of hundred psi. Large transports run their systems at 3,000 psi and, on the newest big jets, 5,000 psi. Higher pressure means the same force from smaller, lighter pipes and actuators, which matters when every kilogram costs fuel.

Fighters are no different. At Seymour Johnson AFB in North Carolina, an Air Force hydraulics shop rebuilds brakes, reservoirs, accumulators, actuators and struts for the F-15E Strike Eagle, F-16 Und A-10, including the servo-cylinders that swing the F-15E’s all-moving stabilators.

Epic Flight Academy’s ground-school lesson on aircraft hydraulic systems.

Why three systems, not one

The great weakness of hydraulics is that a single leak can drain a system. So airliners never rely on one. The Boeing 737 Next Generation has three 3,000 psi systems, called A, B and standby, which power the flight controls, flaps and slats, landing gear, brakes, nosewheel steering, thrust reversers and autopilots. The Boeing 777 also has three, named left, centre and right.

Airbus colour-codes them. The A320 family has green, blue and yellow systems; the green one is pressurised by a pump on the left engine and the yellow by a pump on the right engine, backed by an electric pump. Spreading the jobs across several independent systems means one failure does not take everything with it. Losing them all is the scenario designers work hardest to rule out, and it is exactly what the crew of a DHL A300 hit by a missile over Baghdad in 2003 had to land without.

An ANA Boeing 787 seen from below just after takeoff with its main landing gear retracting
An ANA Boeing 787 tucks its gear away after takeoff. Retracting and extending the landing gear is one of the classic jobs of an airliner’s hydraulic systems. Photo: CCY18999 / Wikimedia Commons, CC BY-SA 3.0

The barking dog

If you have ever heard an Airbus make a loud, rhythmic “whoop-whoop” noise on the ground, you have met the power transfer unit, or PTU. It links two hydraulic systems with a motor and a pump on a shared shaft. The FAA handbook puts it neatly: the PTU transfers power, but not fluid, so a leak in one system cannot drain the other.

On the A320, the PTU sits between the green and yellow systems and starts by itself whenever the pressure difference between them grows too large. That happens most often when only one engine is running, such as during engine start or shutdown. The PTU surges in short bursts, and passengers have been comparing the sound to a barking dog for decades.

Captain Joe explains the Airbus power transfer unit and its famous barking sound.

Purple, fire-resistant and very particular

The fluid itself is a story. The oldest aircraft hydraulic fluid, MIL-H-5606, is mineral oil, dyed red. It works well but burns readily. After a run of hydraulic brake fires in the post-war years, the airline industry pushed for something safer, and the result was phosphate ester fluids such as Skydrol and Hyjet, which are now used in most commercial transport aircraft.

Those fluids are extremely fire-resistant, but not fireproof. They are also fussy. Mineral and phosphate ester fluids do not mix, and the seals for one will not tolerate the other. Service a system with the wrong fluid, the FAA warns, and it must be drained and flushed straight away.

Bigger jets, higher pressure

The A380 is the clearest example of how far hydraulics have come. Airbus chose a 5,000 psi system to save weight, according to a 2002 trade report on the programme, with eight engine-driven pumps supplied by Eaton. It paired two hydraulic flight-control circuits with two electrically powered backup circuits driving electro-hydrostatic actuators, so any one of the four can fly the aircraft.

“Hydraulics is the requirement on the A380, simply due to the massive areas being articulated.”
John Halat — Director of research and new product development, Eaton, on the A380 (Power & Motion, 2002)

That is where hydraulics are heading: towards higher pressures, more electric backups and smarter monitoring. But the core idea has not changed since Pascal. Push on a liquid here, and it pushes just as hard over there. Next time the spoilers snap up on landing, you will know who is doing the heavy lifting.

A compilation of the A320 family’s PTU “barking dog” recorded on board.

Sources: FAA Aviation Maintenance Technician Handbook (Airframe, Vol. 2), Power & Motion, Eaton, Iberia, DVIDS

Header photo: Ken Lund / Wikimedia Commons, CC BY-SA 2.0

Häufig gestellte Fragen

How does an aircraft hydraulic system work?
An aircraft hydraulic system uses Pascal’s law. A pump pressurises an almost incompressible fluid, and pipes carry that pressure to actuators, cylinders whose pistons turn it into movement. Reservoirs, accumulators, filters, heat exchangers and valves keep the fluid clean, cool and going to the right place.
What does hydraulics do on an airliner?
On an airliner, hydraulic systems move the flight controls, extend and retract the landing gear, operate the flaps and slats, power the wheel brakes and nosewheel steering, and deploy the thrust reversers. On the Boeing 737 NG they also serve the autopilots.
What pressure do aircraft hydraulic systems use?
Pressure varies with aircraft size. Small aircraft and helicopters may use a couple of hundred psi, most airliners such as the Boeing 737 NG and 777 run at 3,000 psi, and the largest transports, such as the Airbus A380, use 5,000 psi to save weight.
Why do airliners have three hydraulic systems?
A single leak can drain a hydraulic system, so airliners carry several independent ones for redundancy. The Boeing 737 NG has systems A, B and standby, the 777 has left, centre and right, and the Airbus A320 family uses green, blue and yellow systems.
What is the barking dog sound on an Airbus A320?
The barking sound on an Airbus A320 comes from the power transfer unit, or PTU, which links the green and yellow hydraulic systems. It starts automatically when the pressure difference between them grows, often with only one engine running, and surges in short bursts that sound like barking.
What hydraulic fluid do aircraft use?
Many light aircraft use MIL-H-5606, a red-dyed mineral oil. Most commercial transport aircraft use phosphate ester fluids such as Skydrol, which are extremely fire-resistant but not fireproof. The two types cannot be mixed, and a system serviced with the wrong fluid must be drained and flushed.

Ähnliche Beiträge

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *