Watch the wing from a window seat on almost any jet landing. The wheels thump down, the spoilers flip up, and a second later the back of the engine seems to come apart: a section of the cowling slides backwards, or two big doors swing into the exhaust. Then comes the roar, louder than anything you heard on the approach.
That is reverse thrust, and it is one of the most misunderstood systems on an aircraft. The engine does not spin backwards. The airliner is not relying on it to stop. And on a dry runway, the certified landing distance does not count on it at all. So why does nearly every airliner carry heavy, complex hardware to do it? This is thrust reversers explained, from the clamshell buckets of the 1960s to the reversing propellers of a C-130.
Kurzinfo
- Was es bewirkt: Redirects engine airflow forwards to slow an aircraft after touchdown
- Main jet types: Target (bucket/clamshell), cascade (cold stream) and pivoting door
- Engine direction: The engine never turns backwards; only the airflow is redirected
- Certification: US certification landing distance is demonstrated without reverse thrust
- Most useful: At high speed just after touchdown, and on wet, icy or contaminated runways
- Turboprops: Reverse propeller pitch in the beta range
- Fighters with reversers: Saab 37 Viggen and Panavia Tornado
The basic trick: point the thrust forwards
A jet engine makes thrust by throwing air backwards. A thrust reverser does not change what happens inside the engine; it changes where the air goes when it leaves. Either the exhaust is blocked behind the engine and deflected forwards, or its path is blocked inside the nacelle and it is dumped out of the sides at a forward angle. The engine keeps turning in the same direction, and the pilot then spools it up so there is enough air to redirect.
Pilots select it on the ground by pulling the thrust levers back to idle and then lifting or pulling a separate reverse lever, or moving the thrust levers into a reverse “gate”. It is always a deliberate manual action. Interlocks stop the engine from spooling up until the reverser has actually deployed, because an engine at high power with half a reverser out is the last thing anyone wants.
Animagraffs’ animated breakdown of how airliner thrust reversers redirect engine airflow.
Type one: clamshells and buckets
The oldest and most visible design is the target, or bucket, reverser. Two large doors at the very back of the engine form part of the exhaust nozzle in normal flight. On landing they swing shut behind the jet pipe like a pair of cupped hands, and the hot exhaust hits them and is thrown forwards. The Boeing 737-200’s JT8D buckets are the classic example; the original 707 used the same principle.

Getting it right was not trivial. The first 737s used reversers taken from the 727, and they proved relatively ineffective: they tended to lift the aircraft and take weight off the main wheels, which made the brakes less effective. In 1968 Boeing added a tailpipe extension of about 48 inches and new target-style reversers angled to throw the exhaust over and under the wing. It became standard on all aircraft from March 1969.
The internal clamshell is a close cousin. Instead of doors behind the engine, deflectors inside the jet pipe block the exhaust and send it out through openings in the side of the nacelle, sometimes through vanes that steer the flow forwards. Clamshells and buckets suit turbojets and low-bypass engines, where most of the thrust comes out of the hot core.
Type two: cascades and the cold stream
Modern airliner engines are high-bypass turbofans, and most of their thrust comes from the big fan at the front, not the core. So most of them reverse only the fan air, the “cold stream”. In a cascade reverser, a sleeve around the back of the nacelle slides aft to uncover rows of curved vanes, the cascades. Blocker doors fold down inside the bypass duct, and the fan air is turned outwards and forwards through the vanes.
That is what you see from the cabin when a slice of the engine cowling slides back to reveal a grille. The catch is that the hot core exhaust keeps pushing forwards the whole time, so a cold-stream reverser is less effective than you might think. Some designs add a spoiler to deflect the core flow too. Cascade systems are reliable and strong, but heavy, and hard to fit around the very largest fans.

Type three: pivoting doors
Airbus took a different route on its early single-aisles and the A340. The CFM56 engines on the A320 and A340 use pivoting-door reversers: doors set into the cowling that swing on pivots to block the fan duct and open a path to the outside, scooping the fan air out and forwards. With the doors closed, all you see are the outlines cut into the cowling.
Not every engine on an aircraft has to have a reverser either. The four-engined Airbus A380 only has reversers on its two inboard engines, which reduces the debris stirred up on landing and saves weight and maintenance on the outboard engines. Three-engined Dassault Falcon business jets have one on the centre engine only, and the BAe 146 does without them entirely, using a big air brake in its tail instead, as Afterburner explained in its guide to speed brakes.

How much do thrust reversers really stop you?
Here is the surprise. On a normal landing on a dry runway, wheel brakes alone can stop an airliner. That is how the certified landing distance is set: in the US, landing performance for certification has to be demonstrated without reverse thrust. Manufacturers fly the test landing on a dry, level runway with maximum manual braking, then multiply that distance by 1.67 to get the regulatory dry landing distance, and by a further 1.15 for a wet runway.
Reverse thrust is the margin on top. It works best at high speed, right after touchdown, when the wings are still carrying some of the weight and the brakes cannot grip as well. As the aircraft slows, its effect fades, and pilots cancel it to stop the engine from ingesting debris and its own reversed exhaust.
The autobrake point is the real “aha”. An autobrake does not apply a fixed pressure; it aims for a set rate of deceleration. If the reversers add drag, the autobrake simply squeezes the brakes less to hold the same rate. As long as the brakes could have reached that rate on their own, the stopping distance barely changes, but the brakes do less work and run cooler. Reverse thrust is saving wear, not runway, until the runway turns slippery. Then the brakes cannot reach their target, and the reversers start earning their keep.
That is why regulators treat them carefully. Since 2015, FAA guidance on landing distances calculated at the time of arrival, when pilots know the actual runway condition, allows credit for reverse thrust, but only if the reverser’s failure rate is on the order of one in 10,000 landings or better, and with realistic delays built in for the pilot to select it and for the engine to spool up. Afterburner covered how crews read those runway conditions in its explainer on runway condition codes.
Idle reverse versus max reverse
Pilots do not always use full reverse. Selecting reverse idle deploys the reverser with the engines at idle, which removes the residual forward thrust that an idling jet still produces and adds a little drag. Pulling further spools the engines up to maximum reverse. Many airports restrict full reverse for noise, so on a long dry runway idle reverse is common, with maximum reserved for short or wet runways, high weights and emergencies such as a rejected take-off.

Using less than full power also reduces stress and wear on the engines. Some crews select idle reverse in icy conditions purely to kill that residual thrust. The trade-off is that the deceleration has to come from the brakes, which is exactly why reverse thrust is an option rather than an obligation on a long, dry runway.
Propellers do it too: the beta range
Turboprops reverse thrust in a much simpler way: they twist the propeller blades. The FAA’s Airplane Flying Handbook explains that when the power lever is moved aft of flight idle, it stops asking the governor for a speed and starts controlling blade angle directly. This is the “beta” range. Move the lever further back and the blades go through flat pitch to a negative angle, and the propeller pushes air forwards.
Beta range is why a turboprop such as the Pilatus PC-6 Porter or a Cessna Caravan can stop so short, and why the FAA notes that beta operation dramatically reduces the need for braking compared with piston aircraft of similar weight. It also lets turboprops back up. The C-130 Hercules has fully reversible propellers, and crews can use reverse pitch to back the aircraft up without a tug, as the video below shows.
An RCAF C-130J Hercules backs into its parking spot using reverse propeller pitch (David Hills).
The jet that drives backwards
Big jets almost never reverse under their own power. Using reversers to push back from the gate, the so-called powerback, is possible, but it is noisy, burns fuel and risks blowing debris and slush around. Afterburner explained why airliners use tugs instead.
Der C-17 Globemaster III is the famous exception. Its reversers direct the exhaust upwards and forwards, away from the ground, which reduces debris ingestion and gives enough reverse thrust to back the aircraft up on a narrow taxiway with a three-point turn. The C-17 can also use idle reverse in flight for steep tactical descents. The C-5 Galaxy has an in-flight reverse capability on its inboard engines, the DC-8 was certified for in-flight reverse from 1959, and Concorde used reverse idle on its inboard engines in subsonic flight to steepen its descent.
The C-17 demo team shows off the Globemaster’s reverse thrust at EAA AirVenture (EAA).
Fighters with a reverse gear
Most fighters do without reversers. They add weight, complexity and maintenance cost to aircraft where every kilogram counts. Fighters rely on wheel brakes, speed brakes and, on some types, drag chutes, as Afterburner showed in its look at fighter take-off and landing distances.
Two famous exceptions prove the rule, and both were built for short, vulnerable runways. The Saab 37 Viggen had a reverser in its Volvo RM8 engine so it could operate from 500-metre strips, including straight stretches of Swedish road. According to aviation author Christopher Chant, the RM8 was the first engine fitted with both an afterburner and a thrust reverser. Viggen pilots could pre-select the reverser in the air so that it fired automatically when the nose-wheel strut compressed on touchdown.

Der Panavia Tornado took the same approach. Its RB199 engines carry bucket-type reversers, and combined with its swing wings swept fully forward and full-span flaps and slats, they gave it outstanding short-field landing performance. Testing showed the reversers could destabilise the jet on the landing roll, so a nose-wheel steering augmentation system linked to the yaw damper was added to keep it straight.
A Swedish Air Force Historic Flight Saab 37 Viggen lands, uses its thrust reverser to back up and takes off again (TXAVIATIONIMAGES).
The system you hope to never need
Thrust reversers are used for a tiny fraction of an aircraft’s life, yet they shape the design of the engine nacelle, add weight and cost real money to maintain. Airlines still regard them as an essential part of their safety margin, because they deliver the most help in exactly the conditions where everything else is struggling: snow, ice, standing water and an aborted take-off at high speed.
So the next time the cowling slides back and the engines roar after touchdown, you know what is happening. The aircraft could have stopped without it. The reversers are there for the day it couldn’t, and to make sure the brakes are still cool when that day comes.
Sources: FAA Advisory Circular 25-32, FAA Airplane Flying Handbook (FAA-H-8083-3C), Flight Safety Foundation AeroSafety World, Boeing, Christopher Chant
Header photo: Olivier Cleynen / Wikimedia Commons, CC BY-SA 4.0




0 Comments